
Poolex IceSpa 7 kW Heat Pump Chiller
Heat pump that cools a cold tub to 4 °C and heats a hot tub to 40 °C.
Choose a pump
Pick one to continue.
Cools your cold tub to 4 °C. Heats your hot tub to 40 °C.
The Poolex IceSpa 7 kW heat pump cools or heats your tub water and holds it at the temperature you set.
Cooling works reliably when the outside air is above 10 °C. In colder air, the pressure inside the unit drops and cooling power goes down. Heating works in outside air down to -25 °C.
It has no pump of its own. It needs a circulation pump that moves at least 3 m³/h. We use the Filter Max with it.
Key Features
- Cools and heats. Three modes: cooling, heating and auto.
- Water range. In cooling mode you set the water anywhere from 4 to 35 °C. In heating mode, from 15 to 40 °C.
- How fast it heats. In normal conditions, about 1 to 2 °C per hour. It goes faster in a small, covered tub and in warm air, and slower in a big tub or in cold air.
- Full inverter. It turns its power up and down, instead of just switching on and off. Full power until the water reaches your temperature, then less to hold it there.
- Titanium heat exchanger. Resists corrosion.
- Two relays in the box. With them, the unit can turn a pump and an electric heater on and off by itself. They don't plug in: an electrician wires them in. The Filter Max doesn't need them. It has its own plug.
- Control. Use the display on the unit or the Poolex app. The unit connects only to 2.4 GHz Wi-Fi.
- Winter cover in the box.
Plug and Play
- Factory fitting, paid separately. Buy it with one of our tubs and our factory fits it: the inlet and outlet pipes on the tub, then a test run of the whole system before it ships. Custom wishes cost extra.
- We disconnect the unit from the tub for delivery. You connect it again before you fill the tub.
- Plug the unit into an earthed outdoor socket within 5 m. The Filter Max needs a second one. Keep both sheltered from rain and splashes.
- The plug has a built-in safety switch (RCD) and a 5 m cord.
- The unit stands on its own next to the tub, on firm, level ground. A concrete slab is best.
Before You Buy
- A circulation pump that moves at least 3 m³/h. The unit has none. We use the Filter Max with it.
- Space around the unit. At least 1.5 m free in front. At least 50 cm free at the sides and back. Nothing on top.
- Heating in cold weather. Below 10 °C outside it still heats, but slowly on its own. For faster heating, add an electric heater. The relay in the box switches it on. For safety, an electrician must wire the heater to the relay.
- Water pH between 6.9 and 8.0. This protects the unit.
- Winter. If it runs through a frost, keep the water moving all the time. Water that stops can freeze and crack the unit, the pump and the hoses. If you drain the tub for winter, take the unit off the tub and store it dry.
- Insulation and a lid help. An insulated tub, insulated pipes and a cover help the unit work at its best. See our PUR tub insulation and our lids.
Refrigerant (F-gas Information)
EU law asks us to show this for units with this kind of refrigerant.
- Contains fluorinated greenhouse gases.
- Gas: R32 (HFC-32)
- Amount: 0.65 kg, equal to 0.44 t CO2 equivalent
- Global warming potential (GWP): 675
Downloads
Technical Specifications
- Type: Full-inverter heat pump chiller. No circulation pump.
- Modes: Cooling, heating, auto
- Water temperature range, cooling: 4-35 °C
- Water temperature range, heating: 15-40 °C
- Air temperature range, heating: -25 to 43 °C
- Air temperature range, cooling: 5 to 43 °C
- Cooling capacity (air 35 °C, water 27 °C): 3.2-3.7 kW
- Heating capacity (air 26 °C, water 26 °C): 3.3-7 kW, COP 5-11.9
- Heating capacity (air -10 °C, water 38 °C): 2.2-3.3 kW, COP 1.8-2.1
- Circulation pump needed: at least 3 m³/h
- Power supply: Single phase, 220-240 V ~50 Hz
- Max power: 1.7 kW, 9 A
- Refrigerant: R32 (HFC-32), 0.65 kg
- Compressor: Rotary, EVI (GMCC)
- Heat exchanger: Titanium
- Connections: 1" female thread
- Sound level: Under 48 dB(A) at 1 m, under 36 dB(A) at 4 m, under 28 dB(A) at 10 m
- Protection rating: IPX4
- Dimensions: 705 × 490 × 505 mm
- Net weight: 43 kg
- Control: Digital display on the unit, Wi-Fi and Poolex app (2.4 GHz only)
- CE marking: The unit carries its maker's CE marking.
What's Included
- Winter cover
- 2 × 1" male-thread connections
- 2 control relays
- Water hose
- Bent hose fitting (elbow). Use it if the hose needs to turn a corner.
- Manual